Boral Gutter Replacement Nationwide

Boral Gutter Replacement: The Houston Owner’s Guide

Boral gutter replacement in Houston typically runs $14 to $28 per linear foot installed, which puts most single-story homes between $1,800 and $4,200 for a full gutter run replacement. We stock Boral-compatible gutter profiles on our trucks and can swap a failed section same-day in most cases, as long as we can match the profile and color to what’s already on the house.

Call (254) 566-3573

Most Houston homeowners don’t wake up thinking about gutter replacement. They notice a drip line staining the fascia after a hard rain, or they spot a section sagging away from the eave while rinsing off pollen in March. Boral gutters are solid products, but two decades of Gulf Coast sun, oak-pollen grit, and those sudden downpours that drop two inches in an hour take a toll on the brackets, the sealant, and the metal itself. Over in Sharpstown and Meyerland, we see the same pattern: the south-facing gutters go first, because that’s where the UV hits hardest.

If you’re looking at a Boral gutter that’s pulling loose, leaking at the joints, or rusting through at the end caps, this page will tell you what it costs, whether we can match what’s already there, and what the replacement actually involves. Written price before we start, same as every job Greg Holloway and our crew take on.

Which Boral Models This Applies To

Boral has manufactured gutters under a few different product lines over the years, and the profile names matter when you’re trying to match a replacement. The majority of Houston homes with Boral gutters fall into two camps: the Boral Classic K-style in 5-inch and 6-inch widths, and the Boral Half-Round series, which shows up more on older ranch-style homes and Mediterranean-inspired builds around Bellaire and West University.

The quickest way to identify what you have is to look inside the gutter. Boral stamps the profile name and gauge into the metal on most runs manufactured after 2005. If you can’t read the stamp, measure the top opening. 5-inch K-style gutters measure 5 inches across the top rim. 6-inch versions flare to 6 inches but carry more water, which matters on long rooflines. Half-round is exactly what it sounds like: a semicircle profile.

On the OEM versus aftermarket question: Boral no longer manufactures aluminum gutters directly, so an exact OEM replacement is usually not available. What happens in practice is that we match the gauge, profile shape, and color using a quality aluminum coil from Corten or a comparable manufacturer. The functional result is the same: the new sections clip into existing Boral hangers if the holes are still solid. One compatibility gotcha we run into in Houston: Boral’s older 5-inch gutters used a slightly narrower hanger spacing (18 inches instead of the standard 24). If we’re replacing a run, we’ll add hangers at the tighter spacing so the new aluminum doesn’t oil-can in the heat. Tilehurst Roofing Houston is an independent service provider and installer, not affiliated with Boral.

Signs Your Boral Gutter Replacement Is Failing

• Water spilling over the front edge during rain, not at the downspout. This usually means the pitch has flattened out. Boral’s aluminum hangers can loosen over time as the fascia board behind them swells and shrinks with Houston’s humidity swings, and the gutter loses its slope toward the outlet.
• Joint separation in the middle of a run. Long stretches of Boral gutter were often joined with sealant rather than expansion joints. After enough thermal cycles, that sealant turns brittle and the water finds the gap. This is the single most common repair we do after the first big fall rain.
• Rust staining around end caps or outlet drops. The end caps on Boral gutters are thinner than the run sections and tend to pool water, which makes them the first point to rust through, especially on north-facing eaves that never fully dry.
• Sagging sections you can see from the driveway. When consecutive hangers pull loose from the fascia, the gutter dips low enough to hold standing water. It’s not a cosmetic problem; it’s concentrated weight, and it will eventually tear the gutter apron off the roof edge.
• Granular grit collecting in the gutter beds. If you have Boral or any other clay or concrete tile roof, tile erosion puts fine grit into the gutters. When the runs sag or lose pitch, that grit gets heavy when wet and speeds up every other failure. We see this constantly along the Meyerland corridor.

Replacement Cost & What’s Included

For a Boral gutter replacement in Houston, expect to pay roughly $14 to $28 per linear foot for a full section replacement with new aluminum, including removal of the old run, installation of new hangers and end caps, and reconnecting to the existing downspout. A typical ranch home with 150 linear feet of gutters lands between $2,100 and $4,200. Smaller partial repairs, like replacing an end cap or re-securing hangers on a 10-foot stretch, run $180 to $420.

The price spread comes down to a few things: whether the fascia board behind the gutter is still solid (if it’s rotted, we replace the rotted section before hanging anything), the height of your roof, and the color match. Boral’s off-white and dark bronze are easier matches than the custom grays from the mid-2000s, which sometimes require a closer stock coil at a slightly higher price. Every quote includes the tear-off, haul-away, hangers, end caps, sealant, and a walkthrough afterward. You’ll know the price before we touch the roof. It’s in writing, and it does not change unless you request extra work.

DIY or Call Us?

Replacing gutters involves working on a ladder at roof height, and that’s where we draw a hard line. Most gutter failures our crew sees across Houston happen because someone tried to patch a leaking joint with a caulk gun from a ladder they didn’t secure. Gutters are long, awkward pieces of metal. When one shifts while you’re on a ladder, it acts like a lever against you. The fall risk is real, and it’s not worth a few hundred dollars saved.

What you can safely do from the ground is assess the damage. Look for the symptoms above. Check whether the problem is isolated to one section or spans the full run. Clean out the bed grit with a garden hose once the weather’s dry, and take photos of the failing area. Then call us at (254) 566-3573, describe what you’re seeing, and we’ll confirm whether it’s a simple section replacement or something that needs a full-run fix. The estimate is free, and nobody from Tilehurst Roofing will pressure you into more scope than the gutter needs.

FAQs

Get Your Boral Gutters Fixed Right the First Time

If your Boral gutters are leaking, sagging, or rusting through, call Tilehurst Roofing Houston at (254) 566-3573. Greg Holloway walks every job himself, writes the price before a single foot of gutter comes down, and stands behind the work with the 365-Day Done Right Promise. We stock replacement profiles for Boral, GAF, Owens Corning, and CertainTeed, so whatever you have on the house, we can match it. If the repair fails inside the guarantee period, we come back and make it right, no charge. Written quote, written guarantee, and a live person answers the phone.

Written by Greg Holloway, Owner, Tilehurst Roofing Houston at Tilehurst Roofing Houston, serving Houston and nearby areas.